GRAPHTEC CE5000-60 User Manual. Cutting plotter. Also See for CE5000-60. Service manual - 128 pages. Plotter GRAPHTEC Craft ROBO CC100 Quick Application Manual (28 pages) Plotter GRAPHTEC CC300-20 Craft ROBO User Manual. Cutting plotter (55 pages). ROBO Master-Pro is a program developed by Graphtec. The most used version is 4.60.2, with over 98% of all installations currently using this version. Hello everyone! I just bought a new graphtec ce5000-60 and bought flexi starter 10 to cut basic 1 color vinyl graphics. I make all my eps files in illustrator and simply import them into flexi and cut. But now with the new graphtec I am having troubles doing so. I used the the robo pro software it came with to test cut some basic words and it worked fine. When I tried to use flexi it would roll out my entire roll of vinyl until the screen told me 'NO MEDIA' I was using a sheet not a roll. And I tried both settings, telling the machine it wqas a sheet, and telling it was a roll. And the other time it would roll out like 10 inches of the vinyl and then start to cut my image but not in the bottom right hand corner like I wanted. It also was cutting the words horizantly. NOW, After I installed robo master pro and the 'Graphtec cutting plotter pro' when I sent the basic TEXT cut form flexi it is cutting in the bottom right hand corner like i WANTED but is NOT cutting my graphic. It is cutting random numbers and letters really small and from top to bottom, not left to right. It cut this: 'A138. 912: PR: PD: PD1485: ' and so on. Please if anyone uses a graphtec and flexi software please give me any advice you might have. This is becoming very frustrating for me coming from an expensive cutter. I also have orders that need to be shipped out from a week ago. Click to expand.Cool thanks! That solved the problem of it cutting those little letters. But now I am back to my old problems I have a sheet of vinyl in right now. I have a basic text graphic for it to cut in flexi. When i tell the cutter it's 'ROLL 2' and I push send from flexi all the cutter will do is roll out the whole sheet until the sensor doesnt see the vinyl anymore and it tells me NO MEDIA. Now, when I tell the cutter im using a sheet of vinyl it will cut but again, it rolls out a good 3/4 of the viyl and then begins to cut but I want it to cut in the bottom right hand corner. So basically my problem now is where it is starting the cut. I have it set in flexi to cut in the bottom right hand corner, and the origin is set on the bottom right hand corner of the vinyl in the machine but it still decides to roll out a bunch of the vinyl and start magically in the middle or near the middle. Any suggestions? When the cutter was setup using Roll 1 or Roll 2 and a job sent from Flexi. Media would go to end and trip the rear edge sensor 'No Media' When the cutter was setup using Sheet and a job sent from Flexi. Media would feed to end and cut the object in the middle of the vinyl. All settings within Flexi and driver settings were checked and double checked. Turns out, when the settings for COMMAND were set to HP-GL, the Origin Pt option was set to Center. Changed to L.L. (Lower Left) and all good. All posts and other information available at Signs 101 should be viewed as the opinion only of the poster. No claim is made that any information is accurate. As such, each reader should not rely on any information available here as accurate and should independently verify such accuracy. In addition, no claim is made that posts made here will be free from profanity, obscenity, rude, hurtful, libelous or insulting opinions of the poster. Such posts should, however, be reported to an Administrator for review. Neither the owners, employees, officers nor directors of Signs 101 shall be held responsible or liable under any legal theory for any loss or injury resulting from any post, information made available, policy, action or lack of an action at Signs 101. Your use of this website is your acceptance of these terms and conditions of use. Mp3 sagita terbaru. A Eon Media,LLC Company Signs101 Links. Soal kimia farmasi. Grapthec Pro Studio It is the software for creating original designs and has enhanced functions such as auto-shapes, shading, and editing functions. It is like the popular graphics design software as the Adobe Illustrator and CorelDRAW. It can also configure the cutting conditions and other settings on the plotter. Importing of EPS, Ai, CMX, and PDF file types are supported. Graphics created with other popular design software can be imported into this software. Supported OS: Windows10 / 8.1 / 8 / 7 Major features of Graphtec Pro Studio. Creating registration marks in reversed color The Cutting Master 4 is able to create the registration marks either one of the normal style or reversal style. The reversal style mark has the reversed color and it is able to detect the mark on the media such as the type of glossy or shiny. It enables to expand the compatible media for the Print & Cut applications. It able to specify the color of registration mark line and the color of paint around mark after software version 2.10. (A model that supporting color mark: CE LITE-50) [ Compatible models] CE LITE / FCX4000 / CE6000 PLUS / FCX2000 / FC8600. Graphtec Pro Studio Plus (Option) It is enhanced edition of Graphtec Pro Studio.
0 Comments
Leave a Reply. |